Activity-Based Costing and Management Knickknack, Inc., manufactures two products: odds and ends
Confirming PagesChapter 5Activity-Based Costing and ManagementKnickknack, Inc., manufactures two products: odds and ends. The firm uses a single, plantwide overhead rate based on direct-labor hours. Production and product-costing data are as follows:OddsEndsProduction quantity ………………………………………………………………….Direct material ………………………………………………………………………..Direct labor (not including setup time) ………………………………………….Manufacturing overhead* ………………………………………………………….1,000 units$160120 (4 hr. at $30)384 (4 hr. at $96)5,000 units$240180 (6 hr. at $30)576 (6 hr. at $96)Total cost per unit ……………………………………………………………………$664$996*Calculation of predetermined overhead rate:Manufacturing overhead budget:Machine-related costs ………………………………………………………………………………………………………..Setup and inspection ………………………………………………………………………………………………………….Engineering ………………………………………………………………………………………………………………………Plant-related costs ……………………………………………………………………………………………………………..$1,800,000720,000360,000384,000Total ……………………………………………………………………………………………………………………………….$3,264,000209■ Problem 5–54Activity-Based Costing;Activity Cost Pools; PoolRates; Calculation of ProductCosts; Cost Distortion(LO 5-1, 5-2, 5-3,5-4, 5-5)2. II. Setup and inspection:$9,000 per run5. Odds, new target price:$2,420.64Predetermined overhead rate:Budgeted manufacturing overheadBudgeted direect-labor hours$3, 264, 000(1, 000)(4) (5, 0000)(6)$96 per direct-labor hourKnickknack, Inc., prices its products at 120 percent of cost, which yields target prices of $796.80 forodds and $1,195.20 for ends. Recently, however, Knickknack has been challenged in the market for endsby a European competitor, Bricabrac Corporation. A new entrant in this market, Bricabrac has been selling ends for $880 each. Knickknack’s president is puzzled by Bricabrac’s ability to sell ends at such alow cost. She has asked you (the controller) to look into the matter. You have decided that Knickknack’straditional, volume-based product-costing system may be causing cost distortion between the firm’s twoproducts. Ends are a high-volume, relatively simple product. Odds, on the other hand, are quite complexand exhibit a much lower volume. As a result, you have begun work on an activity-based costing system.Required:1.Let each of the overhead categories in the budget represent an activity cost pool. Categorize eachin terms of the type of activity (e.g., unit-level activity).2.The following cost drivers have been identified for the four activity cost pools.Activity Cost PoolMachine-related costsSetup and inspectionEngineeringPlant-related costsCost DriverBudgeted Level of Cost DriverMachine hoursNumber of production runsEngineering change ordersSquare footage of space18,000 hr.80 runs200 change orders3,840 sq. ft.You have gathered the following additional information:• Each odd requires 8 machine hours, whereas each end requires 2 machine hours.• Odds are manufactured in production runs of 25 units each. Ends are manufactured in 125 unit batches.• Three-quarters of the engineering activity, as measured in terms of change orders, is related to odds.• The plant has 3,840 square feet of space, 80 percent of which is used in the production of odds.For each activity cost pool, compute a pool rate.3.Determine the unit cost, for each activity cost pool, for odds and ends.4.Compute the new product cost per unit for odds and ends, using the ABC system.5.Using the same pricing policy as in the past, compute prices for odds and ends. Use the productcosts determined by the ABC system.6.Show that the ABC system fully assigns the total budgeted manufacturing overhead costs of$3,264,000.7.Show how Knickknack’s traditional, volume-based costing system distorted its product costs. (Use